Options
Slab Renew?!? Any thoughts...Experience?
RichR
Posts: 3,987 ✭✭✭✭✭
Anyone familiar with this product to minimize scratch damage on plastic cases?
Does it work...or will it turn your holders into molten slag?!?
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&rd=1&item=350025895380&ssPageName=STRK:MEWA:IT&ih=022
0
Comments
Thanks much...I didn't want to get too creative on my GSA slabs without first knowing someone has used it with success!
An authorized PCGS dealer, and a contributor to the Red Book.
Chris
The product will improve the slabs quite a bit (estimate 60-70%), but they won't become like new again.
Guess I give the product a qualified endorsement.
Pete
Louis Armstrong
A bottle of Novus #1 and #2 should last you a decade.
The only slab on which they have not worked was an early PCC (Premier Coin Certification) slab that used a soft polycarbonate-based plastic that scratched very easily. Otherwise, I have had no issues with the Meguiar's products.
Lane
See http://www.doubledimes.com for a free online reference for US twenty-cent pieces
Worry is the interest you pay on a debt you may not owe.
"Paper money eventually returns to its intrinsic value---zero."----Voltaire
"Everything you say should be true, but not everything true should be said."----Voltaire
Well, just remember that slabs are not airtight. I have a bottle of slabrenew, but I hesitate to use it since we cannot be certain that the chemicals in any scratch remover is safe for the coins in the slab. My gut reaction is that it is safe, but you never know. I wonder what the long term results will be.
Im *certain* is anyone at all has any ill effects, you will certainly hear them!
I only use a drop, seriously, one drop.
.
i tried this stuff and must say the scuffs on slabs better be minor or you will put more on the slab than you remove
.
.
<< <i>Well, just remember that slabs are not airtight. I have a bottle of slabrenew, but I hesitate to use it since we cannot be certain that the chemicals in any scratch remover is safe for the coins in the slab. My gut reaction is that it is safe, but you never know. I wonder what the long term results will be. >>
The "slabs are not airtight" meme is greatly exaggerated. Unless improperly sonically sealed, (very rare) they are airtight as the term is
normally understood, unless someone messes with them in a pressure chamber or something. The only coins I have seen change in
a slab were either doctored, recently dipped or cleaned, or exposed to high heat or sunlight, or had some contaminent already on the coin.
<< <i>I've had good results with Brasso. Their label recommends their product for removing scratches from plastic watch crystals. >>
i agree. brasso works well. i used it on an old ngc slab...and it looks great now.
<< <i>Thanks much...I didn't want to get too creative on my GSA slabs without first knowing someone has used it with success! >>
GSA plastic is soft compared to other slabs, and the black inserts will show off hairlines left from buffing. The best way of polishing PCGS and NGC slabs may not be the best way of polishing GSA slabs.
Keeper of the VAM Catalog • Professional Coin Imaging • Prime Number Set • World Coins in Early America • British Trade Dollars • Variety Attribution
The almost used-up bottle sat while I switched to PlastX. The liquid separated into oily and pasty substances and then the plastic bottle began to harden and get brittle and crack. Hmm.
Also, the nozzle constantly clogged. I gave up cleaning it and just unscrewed the cap.
I would recommend PlastX instead.
Lance.
<< <i>
<< <i>Thanks much...I didn't want to get too creative on my GSA slabs without first knowing someone has used it with success! >>
GSA plastic is soft compared to other slabs, and the black inserts will show off hairlines left from buffing. The best way of polishing PCGS and NGC slabs may not be the best way of polishing GSA slabs. >>
Good point. I have used the product for years now, with great results. However, there are two requirements for this product to work:
1) Patience - Take your time. Put a drop or two on the slab, work it, wipe it off, and repeat as necessary.
2) Use a COTTON cloth or even a damp cotton ball. Cloth containing polyester or whatever, can abraid the slab you are trying to remove scratches from.
This product has saved myself and my friends a lot of money by not having to have coins re-slabbed. Also, many slabs have a barely seen light haze from rubbing against one another. When this is polished out, the coin can actually look much better. I know of people who look for slabs impaired in this matter. They clean them up, the coin looks better, and they then sell at a profit. They are really good at what they do. OMG! Is that "slab doctoring"?
And whatever you do, do NOT use a mechancal device such as a Dremel. It will burn the plastic, even at low speed.
What was said above regarding the black insert on the GSA's is correct. However, sometimes the minor polishing marks are still preferable to the scratches you are taking out.
Larry L.
Coin's for sale/trade.
Tom Pilitowski
US Rare Coin Investments
800-624-1870
and
Meguilars PlastX which you can get in a car store
if you don't want your slabs to get scratched, you can use small zip lock bags that fit the slab
.
think i will give brasso and plastx a try next
.
.
<< <i>This slab is atrocious. The coin is sold and I have to ship it in a couple of days but in the meantime is there anything that can help with the deep type of scratches seen on this slab? I really don't want to send it back to PCGS and then send it again to CAC unless I have to.
I have saved several slabs that looked almost this bad with PlastX and about thirty minutes of repeated light one drop or so polishes. A lot like getting the spit shine on a new pair of jump boots back in the day that is a lot of light rubbing.
<< <i>
<< <i>This slab is atrocious. The coin is sold and I have to ship it in a couple of days but in the meantime is there anything that can help with the deep type of scratches seen on this slab? I really don't want to send it back to PCGS and then send it again to CAC unless I have to.
I have saved several slabs that looked almost this bad with PlastX and about thirty minutes of repeated light one drop or so polishes. A lot like getting the spit shine on a new pair of jump boots back in the day that is a lot of light rubbing.
Also great to take the clouding of your headlights...works great on all clear plastic items
<< <i>if you don't want your slabs to get scratched, you can use small zip lock bags that fit the slab >>
The polyethylene sleeves for sports cards work well and are a good fit.
Worry is the interest you pay on a debt you may not owe.
"Paper money eventually returns to its intrinsic value---zero."----Voltaire
"Everything you say should be true, but not everything true should be said."----Voltaire
Coin's for sale/trade.
Tom Pilitowski
US Rare Coin Investments
800-624-1870
<< <i>This stuff?
Yes and those sports card sleeves actually scratch slabs as they are being slipped on.
Love the site! Provides a great opportunity to research almost anything related to the hobby. Bought a MS64 PL 1883-CC Morgan and was quite worried about the distracting problem on the reverse of the slab. Took the advice here and used PlastX which cleared up every bit of scratching and cloudiness. Minimal rubbing with just a drop of product - took about three quick applications and about 5 to 10 minutes to remove everything! Thank you to all that offered your opinions.
Looks great! PCGS slabs come out great with that product. I’ve yet to see anything that can work on NGC slabs.
I just ordered a bottle of slab renew, should I test it on a old 1964 graded dome slab before I use it on my value coin slabs???
I've used PlastX with good results. And I, too, use the sports card sleeves to protect my slabs.
Pretty neat, an 11+ year old thread and some products almost as old...
If you love HSN you'll love Slab Renew.
Lance.
As with most problems, there are multiple solutions. I have had good results with two products - the PlastX mentioned here and also with 3M Perfect It Rubbing Compound #39360. I like the 3M product a little better as it seems to take out deeper scratches a bit faster.
One other thing that I do to help protect slab surfaces is to put a coat of The Treatment Model Was on them. EZ on and off and it puts a nice hard wax coating down.
“In matters of style, swim with the current; in matters of principle, stand like a rock." - Thomas Jefferson
My digital cameo album 1950-64 Cameos - take a look!
If I ever have a slab with a scratch that bothers me (it will have to be bad), I will use Brasso or Meguiar's...I am not bothered by minor abrasions.... I do have one major cracked slab (right over the cent)... but it was a special gift, so I will just keep it that way. Cheers, RickO
Start simple
I use goo gone first then this
Best place to buy !
Bronze Associate member
Forum sure comes in handy when you have almost any coin related question. Thanks all for sharing knowledge. I now am the proud owner of a new bottle of PlastX that's missing about 5 drops. Might as well go out and hit the Vette before it gets covered up for winter!