Home› U.S. Coin Forum
Options

Slab Renew?!? Any thoughts...Experience?

RichRRichR Posts: 3,987 ✭✭✭✭✭

Anyone familiar with this product to minimize scratch damage on plastic cases?

Does it work...or will it turn your holders into molten slag?!?


http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&rd=1&item=350025895380&ssPageName=STRK:MEWA:IT&ih=022

Comments

  • Options
    123cents123cents Posts: 7,178 ✭✭✭
    I use it all the time and like it. It does wonders on minor scratches.
    image
  • Options
    RichRRichR Posts: 3,987 ✭✭✭✭✭

    Thanks much...I didn't want to get too creative on my GSA slabs without first knowing someone has used it with success!

    image

  • Options
    RichieURichRichieURich Posts: 8,653 ✭✭✭✭✭
    There are a few threads on this, do a search on Slab Renew.

    An authorized PCGS dealer, and a contributor to the Red Book.

  • Options
    nencoinnencoin Posts: 1,342 ✭✭✭✭
    We bought some and were not pleased with the results. Immediately discarded the bottle. We much prefer Novus.

    Chris
  • Options
    RollermanRollerman Posts: 1,908 ✭✭✭✭✭
    I just got this product and it works after a fashion but not a cure all. If you'll look closely at the examples they use, you can see they tweaked the focus to make the "after" slabs look even better. You can achieve the same affect by using a jewelers loop and getting closer or further away from the holdered coin. At one distance the scrathes are quite visable, not visable from just another 1/4 of an inch away. They state the photo's weren't altered and they weren't, but the focus was adjusted some.
    The product will improve the slabs quite a bit (estimate 60-70%), but they won't become like new again.
    Guess I give the product a qualified endorsement.
    Pete
    "Ain't None of Them play like him (Bix Beiderbecke) Yet."
    Louis Armstrong
  • Options
    ambro51ambro51 Posts: 14,590 ✭✭✭✭✭
    I use Mothers Plastic Polish. this is designed for auto headlamp covers but it works great of the slabs. Just a drop, on some clean bathroom tissue and rub about 100 times. Remember to clean the slabs first with something moist and make sure no grit gets in during the polishing. The direction of the ruibbing is very important, go up and down, picture holding the slab up on end....not sideways or in circles. After you polish you get static electricity which will attract dirt and dust to the slab, so be careful about wiping and starting the whole scratched slab thing over again.
  • Options
    BroadstruckBroadstruck Posts: 30,497 ✭✭✭✭✭
    We bought some and were not pleased with the results. Immediately discarded the bottle. We much prefer Novus.

    image

    A bottle of Novus #1 and #2 should last you a decade.
    To Err Is Human.... To Collect Err's Is Just Too Much Darn Tootin Fun!
  • Options
    astroratastrorat Posts: 9,221 ✭✭✭✭✭
    Meguiar's makes a separate plastic cleaner that removes gum, residue, and takes care of "deeper" scratches. They also make a plastic polish that handles small, light scratches and really brightens the plastic.

    The only slab on which they have not worked was an early PCC (Premier Coin Certification) slab that used a soft polycarbonate-based plastic that scratched very easily. Otherwise, I have had no issues with the Meguiar's products.

    Lane
    Numismatist Ordinaire
    See http://www.doubledimes.com for a free online reference for US twenty-cent pieces
  • Options
    PerryHallPerryHall Posts: 47,871 ✭✭✭✭✭
    I've had good results with Brasso. Their label recommends their product for removing scratches from plastic watch crystals.

    Worry is the interest you pay on a debt you may not owe.
    "Paper money eventually returns to its intrinsic value---zero."----Voltaire
    "Everything you say should be true, but not everything true should be said."----Voltaire

  • Options
    numismanumisma Posts: 3,877 ✭✭✭✭

    Well, just remember that slabs are not airtight. I have a bottle of slabrenew, but I hesitate to use it since we cannot be certain that the chemicals in any scratch remover is safe for the coins in the slab. My gut reaction is that it is safe, but you never know. I wonder what the long term results will be.
  • Options
    ambro51ambro51 Posts: 14,590 ✭✭✭✭✭
    Put up a post asking for horror stories about coins changing color or tarnishing after the slabs have been cleaned.

    Im *certain* is anyone at all has any ill effects, you will certainly hear them!

    I only use a drop, seriously, one drop.
  • Options
    originalisbestoriginalisbest Posts: 5,970 ✭✭✭✭
    Don't immerse the slab in whatever you're removing scratches with and you're fine. Common sense says a modest amount, used appropriately, will in time evaporate/gas out and no potentially harmful residue would remain.
  • Options
    Does Mothers polish, Slab-Renew, Meguiars, or Novus work on PCI slabs?
    Trustworthy BST sellers: cucamongacoin
  • Options
    JeremyDie1JeremyDie1 Posts: 2,383 ✭✭✭
    Slab Renew purpose is to remove light scratches on plastic. So yes.
  • Options
    LanceNewmanOCCLanceNewmanOCC Posts: 19,999 ✭✭✭✭✭
    .
    .
    i tried this stuff and must say the scuffs on slabs better be minor or you will put more on the slab than you remove
    .
    .

    <--- look what's behind the mask! - cool link 1/NO ~ 2/NNP ~ 3/NNC ~ 4/CF ~ 5/PG ~ 6/Cert ~ 7/NGC 7a/NGC pop~ 8/NGCF ~ 9/HA archives ~ 10/PM ~ 11/NM ~ 12/ANACS cert ~ 13/ANACS pop - report fakes 1/ACEF ~ report fakes/thefts 1/NCIS - Numi-Classes SS ~ Bass ~ Transcribed Docs NNP - clashed coins - error training - V V mm styles -

  • Options
    FrankcoinsFrankcoins Posts: 4,575 ✭✭✭


    << <i>Well, just remember that slabs are not airtight. I have a bottle of slabrenew, but I hesitate to use it since we cannot be certain that the chemicals in any scratch remover is safe for the coins in the slab. My gut reaction is that it is safe, but you never know. I wonder what the long term results will be. >>



    The "slabs are not airtight" meme is greatly exaggerated. Unless improperly sonically sealed, (very rare) they are airtight as the term is
    normally understood, unless someone messes with them in a pressure chamber or something. The only coins I have seen change in
    a slab were either doctored, recently dipped or cleaned, or exposed to high heat or sunlight, or had some contaminent already on the coin.
    Frank Provasek - PCGS Authorized Dealer, Life Member ANA, Member TNA. www.frankcoins.com
  • Options
    stevebensteveben Posts: 4,667 ✭✭✭✭✭


    << <i>I've had good results with Brasso. Their label recommends their product for removing scratches from plastic watch crystals. >>



    i agree. brasso works well. i used it on an old ngc slab...and it looks great now.
  • Options
    messydeskmessydesk Posts: 20,919 ✭✭✭✭✭


    << <i>Thanks much...I didn't want to get too creative on my GSA slabs without first knowing someone has used it with success! >>



    GSA plastic is soft compared to other slabs, and the black inserts will show off hairlines left from buffing. The best way of polishing PCGS and NGC slabs may not be the best way of polishing GSA slabs.
  • Options
    lkeigwinlkeigwin Posts: 16,895 ✭✭✭✭✭
    I used a bottle of Slab Renew. It works fine but no better than PlastX from Meguiar's, which is cheaper and readily available from auto parts stores.

    The almost used-up bottle sat while I switched to PlastX. The liquid separated into oily and pasty substances and then the plastic bottle began to harden and get brittle and crack. Hmm.

    Also, the nozzle constantly clogged. I gave up cleaning it and just unscrewed the cap.

    I would recommend PlastX instead.
    Lance.
  • Options
    littlebearlittlebear Posts: 1,605 ✭✭✭✭✭


    << <i>

    << <i>Thanks much...I didn't want to get too creative on my GSA slabs without first knowing someone has used it with success! >>



    GSA plastic is soft compared to other slabs, and the black inserts will show off hairlines left from buffing. The best way of polishing PCGS and NGC slabs may not be the best way of polishing GSA slabs. >>



    Good point. I have used the product for years now, with great results. However, there are two requirements for this product to work:
    1) Patience - Take your time. Put a drop or two on the slab, work it, wipe it off, and repeat as necessary.
    2) Use a COTTON cloth or even a damp cotton ball. Cloth containing polyester or whatever, can abraid the slab you are trying to remove scratches from.

    This product has saved myself and my friends a lot of money by not having to have coins re-slabbed. Also, many slabs have a barely seen light haze from rubbing against one another. When this is polished out, the coin can actually look much better. I know of people who look for slabs impaired in this matter. They clean them up, the coin looks better, and they then sell at a profit. They are really good at what they do. OMG! Is that "slab doctoring"?

    And whatever you do, do NOT use a mechancal device such as a Dremel. It will burn the plastic, even at low speed.

    What was said above regarding the black insert on the GSA's is correct. However, sometimes the minor polishing marks are still preferable to the scratches you are taking out.


    Larry L.


    image
    Autism Awareness: There is no limit to the good you can do, if you don't care who gets the credit.
  • Options
    mrearlygoldmrearlygold Posts: 17,862 ✭✭✭
    This slab is atrocious. The coin is sold and I have to ship it in a couple of days but in the meantime is there anything that can help with the deep type of scratches seen on this slab? I really don't want to send it back to PCGS and then send it again to CAC unless I have to.

    image

    image
  • Options
    lcoopielcoopie Posts: 8,875 ✭✭✭✭✭
    I recommend using a microfiber cloth
    and
    Meguilars PlastX which you can get in a car store

    if you don't want your slabs to get scratched, you can use small zip lock bags that fit the slab
    LCoopie = Les
  • Options
    LanceNewmanOCCLanceNewmanOCC Posts: 19,999 ✭✭✭✭✭
    .
    .
    think i will give brasso and plastx a try next
    .
    .

    <--- look what's behind the mask! - cool link 1/NO ~ 2/NNP ~ 3/NNC ~ 4/CF ~ 5/PG ~ 6/Cert ~ 7/NGC 7a/NGC pop~ 8/NGCF ~ 9/HA archives ~ 10/PM ~ 11/NM ~ 12/ANACS cert ~ 13/ANACS pop - report fakes 1/ACEF ~ report fakes/thefts 1/NCIS - Numi-Classes SS ~ Bass ~ Transcribed Docs NNP - clashed coins - error training - V V mm styles -

  • Options
    LindeDadLindeDad Posts: 18,766 ✭✭✭✭✭


    << <i>This slab is atrocious. The coin is sold and I have to ship it in a couple of days but in the meantime is there anything that can help with the deep type of scratches seen on this slab? I really don't want to send it back to PCGS and then send it again to CAC unless I have to.

    image

    image >>



    I have saved several slabs that looked almost this bad with PlastX and about thirty minutes of repeated light one drop or so polishes. A lot like getting the spit shine on a new pair of jump boots back in the day that is a lot of light rubbing.
    image
  • Options
    OPAOPA Posts: 17,178 ✭✭✭✭✭


    << <i>

    << <i>This slab is atrocious. The coin is sold and I have to ship it in a couple of days but in the meantime is there anything that can help with the deep type of scratches seen on this slab? I really don't want to send it back to PCGS and then send it again to CAC unless I have to.

    image

    image >>



    I have saved several slabs that looked almost this bad with PlastX and about thirty minutes of repeated light one drop or so polishes. A lot like getting the spit shine on a new pair of jump boots back in the day that is a lot of light rubbing.
    image >>

    image

    Also great to take the clouding of your headlights...works great on all clear plastic items
    "Bongo drive 1984 Lincoln that looks like old coin dug from ground."
  • Options
    MikeInFLMikeInFL Posts: 10,192 ✭✭✭✭
    Just go get some PlastX and save yourself some money....IMO of course. image
    Collector of Large Cents, US Type, and modern pocket change.
  • Options
    PerryHallPerryHall Posts: 47,871 ✭✭✭✭✭


    << <i>if you don't want your slabs to get scratched, you can use small zip lock bags that fit the slab >>



    The polyethylene sleeves for sports cards work well and are a good fit.

    Worry is the interest you pay on a debt you may not owe.
    "Paper money eventually returns to its intrinsic value---zero."----Voltaire
    "Everything you say should be true, but not everything true should be said."----Voltaire

  • Options
    mrearlygoldmrearlygold Posts: 17,862 ✭✭✭
    This stuff?

    image
  • Options
    LindeDadLindeDad Posts: 18,766 ✭✭✭✭✭


    << <i>This stuff?

    image >>



    Yes and those sports card sleeves actually scratch slabs as they are being slipped on.
    image
  • Options
    mark_dakmark_dak Posts: 1,160 ✭✭✭✭✭

    Love the site! Provides a great opportunity to research almost anything related to the hobby. Bought a MS64 PL 1883-CC Morgan and was quite worried about the distracting problem on the reverse of the slab. Took the advice here and used PlastX which cleared up every bit of scratching and cloudiness. Minimal rubbing with just a drop of product - took about three quick applications and about 5 to 10 minutes to remove everything! Thank you to all that offered your opinions.


  • Options
    Downtown1974Downtown1974 Posts: 7,186 ✭✭✭✭✭

    Looks great! PCGS slabs come out great with that product. I’ve yet to see anything that can work on NGC slabs.

  • Options
    ShipwreckCoinHunterShipwreckCoinHunter Posts: 1,990 ✭✭✭✭✭

    I just ordered a bottle of slab renew, should I test it on a old 1964 graded dome slab before I use it on my value coin slabs???

  • Options
    koynekwestkoynekwest Posts: 10,048 ✭✭✭✭✭

    I've used PlastX with good results. And I, too, use the sports card sleeves to protect my slabs.

  • Options
    HemisphericalHemispherical Posts: 9,370 ✭✭✭✭✭

    Pretty neat, an 11+ year old thread and some products almost as old...

  • Options
    lkeigwinlkeigwin Posts: 16,895 ✭✭✭✭✭

    If you love HSN you'll love Slab Renew.
    Lance.

  • Options
    CameonutCameonut Posts: 7,440 ✭✭✭✭✭

    As with most problems, there are multiple solutions. I have had good results with two products - the PlastX mentioned here and also with 3M Perfect It Rubbing Compound #39360. I like the 3M product a little better as it seems to take out deeper scratches a bit faster.

    One other thing that I do to help protect slab surfaces is to put a coat of The Treatment Model Was on them. EZ on and off and it puts a nice hard wax coating down.

    “In matters of style, swim with the current; in matters of principle, stand like a rock." - Thomas Jefferson

    My digital cameo album 1950-64 Cameos - take a look!

  • Options
    rickoricko Posts: 98,721 ✭✭✭✭✭

    If I ever have a slab with a scratch that bothers me (it will have to be bad), I will use Brasso or Meguiar's...I am not bothered by minor abrasions.... I do have one major cracked slab (right over the cent)... but it was a special gift, so I will just keep it that way. Cheers, RickO

  • Options
    KkathylKkathyl Posts: 3,762 ✭✭✭✭✭
    edited November 24, 2019 4:59AM

    Start simple
    I use goo gone first then this

    Best place to buy !
    Bronze Associate member

  • Options
    mark_dakmark_dak Posts: 1,160 ✭✭✭✭✭

    Forum sure comes in handy when you have almost any coin related question. Thanks all for sharing knowledge. I now am the proud owner of a new bottle of PlastX that's missing about 5 drops. Might as well go out and hit the Vette before it gets covered up for winter!

  • Options
    ms70ms70 Posts: 13,957 ✭✭✭✭✭

Leave a Comment

BoldItalicStrikethroughOrdered listUnordered list
Emoji
Image
Align leftAlign centerAlign rightToggle HTML viewToggle full pageToggle lights
Drop image/file