Home› U.S. Coin Forum
Options

What Is The Safest Way To Crack Out A Coin From A PCGS Holder?

CoinlearnerCoinlearner Posts: 2,612 ✭✭✭✭✭
Never tried it yet but thinking about wrapping in towel and hitting with hammer or putting in vice.

Comments

  • Options
    BECOKABECOKA Posts: 16,972 ✭✭✭
    I put it in a plastic bag, turn it on its side and use a hammer on the edges. If you pound around the edge on all sides eventually you will hear a pop. The plastic bag keeps the shards from flying. image

    This is not the bets way but it works for me.
  • Options
    GRANDAMGRANDAM Posts: 8,785 ✭✭✭✭✭
    I use a pair of bolt cutters.

    image

    Simply cut the slab in the middle of where the coin is and it splits all the way across. The coin then pulls right out. Never had a problem or scratched a coin. No muss, no fuss, no shavings or dust as with a saw.

    Bolt cutters don't work on NGC slabs as they are a different plastic and it doesn't crack like the PCGS plastic does.

    GrandAm image
    GrandAm :)
  • Options
    BECOKABECOKA Posts: 16,972 ✭✭✭


    << <i>I use a pair of bolt cutters.

    image

    Simply cut the slab in the middle of where the coin is and it splits all the way across. The coin then pulls right out. Never had a problem or scratched a coin. No muss, no fuss, no shavings or dust as with a saw.

    Bolt cutters don't work on NGC slabs as they are a different plastic and it doesn't crack like the PCGS plastic does.

    GrandAm image >>



    For NGC slabs a quick hammer tap on all for sides will break the seal and you can pull the slab into its two pieces no problem.
  • Options
    CameonutCameonut Posts: 7,440 ✭✭✭✭✭
    Channel Lock End Cutter - here is a pic from Amazon.com. One nip at 3 o'clock or 9 o'clock and the rubber insert is free. Make sure to cover the slab with a towel, the plastic pieces can be extremely sharp. Also wear safety glasses. Preferred by at least one major dealer/auction house.

    image

    “In matters of style, swim with the current; in matters of principle, stand like a rock." - Thomas Jefferson

    My digital cameo album 1950-64 Cameos - take a look!

  • Options
    If you know the hammer trick it actually works great.

    Don't try unless you've been shown or are brave. But,
    after hitting it on the edges you'll hear a distinct pop. Then
    you can literally just hold the slab in the palm of your hand
    and lift off the top!



    Jerry



  • Options
    I can tell you not to do it like these idiots.

    Link
    imageimageimageimageimageimage
  • Options
    originalisbestoriginalisbest Posts: 5,970 ✭✭✭✭
    I prefer a vise, with a clear bag around the slab so you can tell what's happening. Nice and controlled, no need to send a coin flying or scratch it. Gotta have the plastic bag in case any shards go flying -- eyes are important things.
  • Options
    cmerlo1cmerlo1 Posts: 8,089 ✭✭✭✭✭
    I use a dremel with a cutoff wheel. Cut around the outside, put a screwdriver in the groove you made (away from the coin) and twist...
    You Suck! Awarded 6/2008- 1901-O Micro O Morgan, 8/2008- 1878 VAM-123 Morgan, 9/2022 1888-O VAM-1B3 H8 Morgan | Senior Regional Representative- ANACS Coin Grading. Posted opinions on coins are my own, and are not an official ANACS opinion.
  • Options
    CoinlearnerCoinlearner Posts: 2,612 ✭✭✭✭✭
    image Thinks for the ideas. Have a few I want to liberate and will try a couple of ways.
  • Options
    derrybderryb Posts: 38,713 ✭✭✭✭✭
    hacksaw, left to right across the lower part of the label. pops right open afterward.

    Governments can print currency. Only the people can print faith in it — and they’re running low on ink.

  • Options
    With some that I want to be very careful I use a electric grinding wheel. It will grind the edges off with no splinter or cracks to damage your coins. It takes about 20-30 seconds and a little stink. image
  • Options
    ConnecticoinConnecticoin Posts: 13,278 ✭✭✭✭✭
    Easist way for me is the hammer around the edges a few times (on a hard surface), then it should fold open like a book. I tried other methods, but the good 'ole hammer is still the easist.
  • Options


    << <i>hacksaw, left to right across the lower part of the label. pops right open afterward. >>

    Yup.
    aka Dan
  • Options
    I keep telling you all.

    A table saw is the quickest and easiest way to go.

    If you've got several, you can do a dozen in just a couple of minutes.

    Can't beat it!
    "Lenin is certainly right. There is no subtler or more severe means of overturning the existing basis of society(destroy capitalism) than to debauch the currency. The process engages all the hidden forces of economic law on the side of destruction, and it does it in a manner which not one man in a million is able to diagnose."
    John Marnard Keynes, The Economic Consequences of the Peace, 1920, page 235ff
  • Options
    FrankcoinsFrankcoins Posts: 4,575 ✭✭✭
    Tile nippers are better suited. Note the direction of the cutting edges

    image
    Frank Provasek - PCGS Authorized Dealer, Life Member ANA, Member TNA. www.frankcoins.com
  • Options
    RarityRarity Posts: 1,466 ✭✭✭✭
    I will open a "Slab breaking service" with a 7-day turn around time for $5 a pop, not counting shipping and insurance fees. image
  • Options
    FrankcoinsFrankcoins Posts: 4,575 ✭✭✭
    I meant to ask....Does CAC pay a 50¢ bounty for stickers from crackouts?
    Frank Provasek - PCGS Authorized Dealer, Life Member ANA, Member TNA. www.frankcoins.com
  • Options
    droopyddroopyd Posts: 5,381 ✭✭✭


    << <i>I use a pair of bolt cutters.

    image

    Simply cut the slab in the middle of where the coin is and it splits all the way across. The coin then pulls right out. Never had a problem or scratched a coin. No muss, no fuss, no shavings or dust as with a saw.

    Bolt cutters don't work on NGC slabs as they are a different plastic and it doesn't crack like the PCGS plastic does. >>



    I think you have the same bolt cutters that I do! They do work on NGC slabs, but because the plastic is softer, the bolt cutters wind up scoring the plastic so you can just snap in half cleanly at the score.
    Me at the Springfield coin show:
    image
    60 years into this hobby and I'm still working on my Lincoln set!
  • Options
    BochimanBochiman Posts: 25,783 ✭✭✭✭✭
    I concentrate real hard, then at the last second, I jam my fingernail into the seam and pop it open

    I've been told I tolerate fools poorly...that may explain things if I have a problem with you. Current ebay items - Nothing at the moment

  • Options
    PerryHallPerryHall Posts: 47,871 ✭✭✭✭✭
    Mail it to yourself with inadequate packaging.

    Worry is the interest you pay on a debt you may not owe.
    "Paper money eventually returns to its intrinsic value---zero."----Voltaire
    "Everything you say should be true, but not everything true should be said."----Voltaire

  • Options
    BECOKABECOKA Posts: 16,972 ✭✭✭


    << <i>I meant to ask....Does CAC pay a 50¢ bounty for stickers from crackouts? >>




    image
  • Options
    PerryHallPerryHall Posts: 47,871 ✭✭✭✭✭


    << <i>I meant to ask....Does CAC pay a 50¢ bounty for stickers from crackouts? >>



    Does anyone know if CAC is going to publish a population report like the real grading companies?

    Worry is the interest you pay on a debt you may not owe.
    "Paper money eventually returns to its intrinsic value---zero."----Voltaire
    "Everything you say should be true, but not everything true should be said."----Voltaire

  • Options
    BoomBoom Posts: 10,165 ✭
    Either use a table vice and tighten down till you hear or feel the seal break (as others stated, for safety's sake either wear safety glasses or wrap the slab.) Finish the job by using a screwdriver.

    Personally, I just whack the top of the slab with a Hammer - w/ safety glasses on, and then carefully finish the job with the screwdriver.

Leave a Comment

BoldItalicStrikethroughOrdered listUnordered list
Emoji
Image
Align leftAlign centerAlign rightToggle HTML viewToggle full pageToggle lights
Drop image/file