Home› U.S. Coin Forum
Options

1858 Seated Half Dime Error

Does anyone have any ideas on what caused this error??? About half of the denticles are missing on both sides.

image

image

Comments

  • Options
    errormavenerrormaven Posts: 1,184 ✭✭✭
    Quite possibly. But you better measure its diameter to be sure. When the periphery of a coin with denticles is weakly struck it can mimic the appearance of broadstrike. Also, check the edge for reeding. If reeding is present it is not a broadstrike.
    Mike Diamond is an error coin writer and researcher. Views expressed here do not necessarily reflect those held by any organization I am a member of.
  • Options
    cmerlo1cmerlo1 Posts: 8,089 ✭✭✭✭✭


    << <i>Also, check the edge for reeding. If reeding is present it is not a broadstrike. >>



    image


    Definitely something cool going on with this coin...looks like it may be broadstruck (the lack of reeding will prove it)...it's not off center, because the entire design is visible.


    --Christian
    You Suck! Awarded 6/2008- 1901-O Micro O Morgan, 8/2008- 1878 VAM-123 Morgan, 9/2022 1888-O VAM-1B3 H8 Morgan | Senior Regional Representative- ANACS Coin Grading. Posted opinions on coins are my own, and are not an official ANACS opinion.
  • Options
    IRCWCoinsIRCWCoins Posts: 895 ✭✭
    I have it in-hand now, and it does have a reeded edge. Could the lack of denticles have been caused by a tapered planchet?
  • Options
    IRCWCoinsIRCWCoins Posts: 895 ✭✭
    TTT
  • Options
    lathmachlathmach Posts: 4,720 ✭
    Hey IRCWCoins......................
    Ask your question over here on the other side.
    Steve Crain lives Seated Half dimes. Let him give you some insight.

    Ray
  • Options
    LanLordLanLord Posts: 11,765 ✭✭✭✭✭
    Various years of seated half dimes are missing large areas of denticles like the picture you have.
  • Options
    CladiatorCladiator Posts: 18,353 ✭✭✭✭✭
    Mayor, light the Mr.HalfDime beacon!

    image
  • Options
    mgoodm3mgoodm3 Posts: 17,497 ✭✭✭
    Common finding on some of the seated half dime dates.
    coinimaging.com/my photography articles Check out the new macro lens testing section
  • Options
    MrHalfDimeMrHalfDime Posts: 3,440 ✭✭✭✭
    There have been several good responses to your original post, but since you brought it back to the top, and since Cladiator illuminated the Mr. Half Dime beacon, I will add a few comments of my own.

    First, as Error Maven and others have pointed out, if there is edge reeding on your coin (as there apparently is from your own observation) then your coin cannot be a broadstrike. A broad-struck coin is one that was struck outside of the collar. The collar, which, along with the obverse and reverse dies defines the 'coining chamber', contains the edge reeding, and it is the collar which imparts the edge reeding to the struck coin as the planchet expands under the pressure of striking. If the coin was struck outside of the collar, there will be no reeding, and the coin will typically be larger in diameter than a normal strike. The mere appearance of blurred or indistinct dentils, as on your coin, does not necessarily indicate a broadstrike.

    Again, as others have already pointed out, blurred or indistinct dentils on half dimes of this period are the norm rather than the exception. After the arrows, used to indicate the reduced silver weight of the planchets, were removed in 1856, and continuing until the obverse was completely redesigned in 1859, many examples are seen with indistinct, almost non-existant dentils. This was a characteristic of the hub(s), and is seen on most working dies. The worst year for weak and indistinct dentils is 1856; there is just one hub (and perhaps just one or at the most two working dies) which exhibit complete dentils, particularly on the obverse. Although the hubs were 'touched up', or reworked, in 1857, the dentils were not one of the details that were 'touched up'. Although the 1857 and 1858 half dimes are typically not quite as weak in the dentils as are the 1856 half dimes, your coin should be considered typical for the period, and although instructive to the understanding of the minting process, it is not rare.

    As to the precise cause of the weak dentils, the working hub, used to produce the working dies, had all of the devices and details in positive relief, just as seen on the struck coins themselves. Thus, the dentils, and the periphery or circumference of the obverse, which defined the outer edges of the dentils, were vulnerable, and subject to wear from both the pressure of striking the working dies, and from reworking and lapping by the die shop. As these details wore down, the same details on the working dies, and therefore the struck coins, also became weaker. The dates involved (1856 - 1858) are very high mintage years for the series, and the working dies were kept in service until they could no longer be used. Thus, a rare half dime of this period would actually be one with fully struck dentils.
    They that can give up essential Liberty to obtain a little temporary safety deserve neither Liberty nor safety. Benjamin Franklin

Leave a Comment

BoldItalicStrikethroughOrdered listUnordered list
Emoji
Image
Align leftAlign centerAlign rightToggle HTML viewToggle full pageToggle lights
Drop image/file