Could you explain?

Options
Piri
Piri Posts: 7 ✭
edited July 10, 2025 7:21AM in Q & A Forum

How did the die error occur on the 1919 D Lincoln One Cent in my collection? Could you explain? Best regards.

UN.jpg 40.8K
IU.jpg 37.6K
PP.jpg 39.4K

Comments

  • 291fifth
    291fifth Posts: 25,218 ✭✭✭✭✭
    Options

    It isn't an error. It is just damage caused by the coin being hit by some hard object during its circulation life.

    All glory is fleeting.
  • Greenstang
    Greenstang Posts: 1,648 ✭✭✭✭✭
    Options

    Welcome to the forum
    It is not an error, it is damage.
    The bulge on the reverse indicates that it has taken a hit on the obverse.
    This greatly devaluates the value of the cent.

  • yosclimber
    yosclimber Posts: 5,322 ✭✭✭✭✭
    edited July 10, 2025 4:00AM
    Options




    Thank you for your clear photos.

    This is not a die error.
    It is "post mint damage".
    What happened was that a heavy impact hit the obverse at Lincoln's lower head and neck.
    The reverse was sitting on a hard flat surface.
    So a large impact mark was created on the lower head and neck.
    And the corresponding (center) of the reverse was flattened.

    You could achieve roughly the same effect by hitting a coin twice with a ball peen hammer with the coin on a flat surface.

  • Coins3675
    Coins3675 Posts: 1,140 ✭✭✭✭
    Options

    That coin looks rough, but is 100% post-mint damage.

    Successful Transactions With: JWP, DBSTrader2, greencopper, bretsan, ajaan, Ted1, Desert Coin, olah_in_MA

  • Aspie_Rocco
    Aspie_Rocco Posts: 3,872 ✭✭✭✭✭
    Options

    I smell a troll. If someone can explain parts of the striking process in that detail, yet still post a PMD coin asking us to explain, troll

    https://www.autismforums.com/media/albums/acrylic-colors-by-rocco.291/

  • jmlanzaf
    jmlanzaf Posts: 43,060 ✭✭✭✭✭
    Options

    @Piri said:
    Another solution
    A small piece of metal was rolled into the planchet, falling out after the strike.When the upper die struck the planchet and the small piece on it, down to the small piece thickness; die design, up to design cavities penetrates into the planchette and creating the error obverse of the coin.
    Durig the stroke, the small piece tries to protrude under the planchet due to its thickness.
    The lower die struck the planchet and crushes this protrusion. And the coin has dents on the reverse side and the bottom die design is missing the error image is created.

    Absolutely not possible. If the die strikes through, the depression would be in one side with no protruding counterpart.

    Think about it. During the strike the dies are simultaneously compressed. You would have to penetrate the hardened steel die with a soft brass planchet. Physically IMPOSSIBLE

    All comments reflect the opinion of the author, even when irrefutably accurate.

  • World67
    World67 Posts: 13,098 ✭✭✭✭✭
    Options

    @Piri said:
    Another solution
    A small piece of metal was rolled into the planchet, falling out after the strike.When the upper die struck the planchet and the small piece on it, down to the small piece thickness; die design, up to design cavities penetrates into the planchette and creating the error obverse of the coin.
    Durig the stroke, the small piece tries to protrude under the planchet due to its thickness.
    The lower die struck the planchet and crushes this protrusion. And the coin has dents on the reverse side and the bottom die design is missing the error image is created.

    Seek immediate medical attention.

  • 291fifth
    291fifth Posts: 25,218 ✭✭✭✭✭
    Options

    If you don't agree with the comments from experienced members of the board then it is time to send it into PCGS for certification. Prepare for a costly disappointment.

    All glory is fleeting.
  • Piri
    Piri Posts: 7 ✭
    Options

    Morgan White
    I just expressed my opinions. Are you a megalomaniac who responds to opinions disrespectfully?

  • Piri
    Piri Posts: 7 ✭
    Options

    jmlanzaf
    Thank you for your enlightening information. I approve.Kind regards.

  • World67
    World67 Posts: 13,098 ✭✭✭✭✭
    Options

    @Piri said:
    Morgan White
    I just expressed my opinions. Are you a megalomaniac who responds to opinions disrespectfully?

Categories